Larry H. Miller Toyota Murray

2010 Toyota 4Runner Oil Filter

Toyota 4Runner Oil Filter service at Larry H. Miller Toyota Murray in Murray, UT

The 2010 Toyota 4Runner is a four-wheel-drive SUV with a 4.0-liter V6 engine, and its oil filter helps keep circulating oil clear of collected debris. At Larry H. Miller Toyota Murray in Murray, UT, an oil filter service replaces the filter matched to this engine, renews the drain plug gasket or washer where applicable, and checks for leaks after the engine runs. Booking this service alongside an oil change helps maintain clean oil circulation through the engine. It is a practical service for drivers who want the filter replaced rather than stretched across multiple oil changes. Schedule service with the dealership service team.

What an oil filter replacement on a 2010 Toyota 4Runner involves

An oil filter replacement for the 2010 Toyota 4Runner begins with fitting a filter matched to the engine's specification. The filter is selected for the engine actually fitted to the SUV, helping it capture the debris carried away by the oil. During the service, the drain plug gasket or washer is also renewed where the engine uses one. That small sealing component supports a proper seal when the drain plug is reinstalled.

After the filter and oil service are complete, the engine is run and the filter seal is checked for leaks. This final inspection helps confirm that the filter and related sealing surfaces remain dry while the engine is operating. The oil grade the manufacturer specifies for this engine should be used as part of the oil service. The manufacturer's maintenance schedule does not state an interval for this model year, so service timing should be guided by that schedule and the vehicle's service history. When the filter is due with the oil, schedule service at Larry H. Miller Toyota Murray.

Why the filter matters on a 2010 Toyota 4Runner

The 2010 Toyota 4Runner uses a 4.0-liter V6 engine with 3,956 cc of displacement. As engine oil moves through its lubrication system, it picks up debris and carries that material toward the filter. The filter holds the debris so cleaner oil can continue circulating through the engine. That is why replacing the filter with the oil is part of maintaining the oil service rather than treating the filter as something to stretch across two changes.

Once a filter loads with debris, its bypass valve opens. The engine still receives oil, but the oil circulates unfiltered. A loaded filter therefore does not necessarily stop oil flow; it quietly allows oil without normal filtration to move through the engine. Replacing the filter at the oil service removes that loaded filtering element and installs one matched to the engine. For this four-wheel-drive SUV, an oil and filter service addresses both the oil and the component that captures what the oil carries away.

Oil and filter service at Larry H. Miller Toyota Murray

At Larry H. Miller Toyota Murray, service for the 2010 Toyota 4Runner can include a filter matched to its 4.0-liter V6 engine, a new drain plug gasket or washer where applicable, and a leak check after the engine has run. The service team can also help connect the vehicle's service history with the manufacturer's maintenance schedule, which does not state an interval for this model year. That keeps the discussion focused on the vehicle's actual maintenance needs rather than a guessed number.

The dealership is located in Murray, UT, at 5650 S. State Street, 84107. To arrange an oil and filter service, schedule an appointment online or call 385-425-0839. You can also review available service specials before booking.

Frequently Asked Questions

6 common questions answered

Is the oil filter replaced every time a 2010 Toyota 4Runner has its oil changed?The oil filter should be replaced with the oil when the service calls for an oil and filter service.

The filter captures debris carried by the oil, and its bypass valve opens when the filter becomes loaded. Replacing it with the oil avoids carrying a used filtering element into another service cycle. The manufacturer's maintenance schedule does not state an interval for this model year, so timing depends on the schedule and the vehicle's service history.

Filter matched to the 4.0-liter V6
Drain plug gasket or washer renewed where applicable
Filter seal checked for leaks after the engine runs

What is included in an oil filter replacement on a 2010 Toyota 4Runner?The service includes a filter matched to the engine, a new drain plug gasket or washer where applicable, and a leak check after the engine runs.

The filter is selected for the engine actually fitted to the SUV. Renewing the sealing component supports the drain plug connection, while running the engine allows the filter seal to be inspected under operating conditions. The oil service uses the oil grade the manufacturer specifies for this engine.

Engine-matched oil filter
New drain plug gasket or washer where used
Post-service filter-seal leak inspection

What happens if the oil filter on a 2010 Toyota 4Runner is not replaced?A loaded filter can open its bypass valve, allowing oil to circulate without normal filtration.

The engine continues receiving oil, but that oil may carry debris through the lubrication system instead of having it held by the filter. This change can happen quietly, without immediately stopping oil flow. Replacing the filter with the oil removes the loaded filtering element and restores filtration with a filter matched to the engine.

Debris remains in circulation more easily
The bypass valve can allow unfiltered oil flow
A used filter is carried into another service cycle

Does a 2010 Toyota 4Runner need a specific oil filter?Yes, the filter is matched to this 4.0-liter, six-cylinder V6 engine, and filters are not interchangeable across engines.

The 2010 Toyota 4Runner has 3,956 cc of displacement, so the filter must suit the engine actually fitted to the SUV. A properly matched filter is designed to capture debris as oil circulates through that engine. The service does not rely on selecting a generic filter without considering engine application.

4.0-liter engine displacement
Six-cylinder V6 layout
Filter application matched to the fitted engine

Can the oil be changed on a 2010 Toyota 4Runner without changing the filter?The oil can be changed separately, but an oil and filter service replaces the filter at the same time.

Changing only the oil leaves the existing filter in place, where it continues holding the debris already captured. Once a filter loads, its bypass valve opens and oil circulates unfiltered. Whether the filter is due depends on the manufacturer's maintenance schedule and the vehicle's service history, and no interval is stated for this model year.

Oil replacement and filter replacement are related services
A used filter retains collected debris
Service history helps determine what is due

How do I book an oil and filter service at Larry H. Miller Toyota Murray?Book online through the service appointment page or call Larry H. Miller Toyota Murray at 385-425-0839.

The dealership is at 5650 S. State Street in Murray, UT 84107. Mention the 2010 Toyota 4Runner and request an oil and filter service so the filter can be matched to its 4.0-liter V6 engine. You can review service specials before you schedule an appointment.

Online scheduler: service appointment page
Phone: 385-425-0839
Location: 5650 S. State Street, Murray, UT 84107